By Arjan Dhillon
In a restaurant build-out, the walk-in is often one of the last things specified and one of the first things built. Once the panels are up, changing the size, the door, or where the compressor goes means moving walls, re-running electrical or re-quoting the refrigeration. So, make decisions in these categories before you ask for a quote, and every quote you get will price the same box.
Size and shape of the room
Start with the actual space, rather than a catalogue size. Walk-ins are built from insulated panels, so the box can follow your room, including an L-shape or a notch around a column. Measure the path to check the route from the back door to the walk-in, instead of just the footprint. Size for delivery day and make a plan for what lands on your busiest delivery, rather than an average Tuesday. Consider the height, too – a taller box adds shelf levels without adding floor area, which matters on expensive restaurant square footage.
Cooler, freezer, or both
Health Canada’s food storage guidance sets refrigeration at 4°C (40°F) or lower and freezing at minus 18°C (0°F) or lower. Decide on what you need now, because the choice drives insulation, the floor, and the refrigeration. How do they differ?
A combination box features one footprint split into a cooler and a freezer by a partition wall, often with the freezer entered through the cooler. A separate system means that each side needs its own refrigeration and its own temperature control.
Panels and insulation
Panels decide how well the box holds its cold. Since 2017, Natural Resources Canada has set minimum insulation for walk-in panels and doors: R-25 for coolers and R-32 for freezers. So, ask for the specifics so that the quote lists panel thickness and R-value, instead of just “insulated panels.”
Consider location when choosing a finish – a walk-in that faces an open kitchen or dining room may need a finish that suits the room, such as stainless steel.
The floor
A freezer needs an insulated floor. The National Research Council’s Canadian Building Digest 61 explains why: the ground under a freezer slab can freeze and heave the floor, and heat under the slab is the standard fix for rooms kept below freezing all year. A cooler can often sit directly on a sound, level concrete slab, which also makes cart access easier, but cracks in the slab, slope, and drains all affect what the floor can be.
Doors
Measure the widest thing that will go through the door: a cart, a dolly, or a rack – and then think about the kitchen around it. Consider the swing direction: a door that swings into a busy line is a hazard; choose the hinge side with traffic in mind. Sliding doors may be a better option because they suit tight corridors where a swing door has no room. What about strip curtains, which limit warm air during a long service when the door stays open. Lastly, freight doors need to e considered.
Canada’s rules treat a walk-in door at least 4 ft. wide and 8 ft. high as a freight door, so plan any pallet access early.
Where the refrigeration goes
This is the decision most often left too late. A self-contained unit sits on the box, which is simpler but puts its heat and noise into your kitchen. A remote condensing unit sits on the roof or outside and connects by refrigerant lines, which keeps the kitchen cooler and quieter. Check the lease to determine whether a rooftop unit needs the landlord’s approval and a roof penetration. Plan the electrical – the refrigeration choice sets the circuits your electrician needs to run.
Shelving and aisles
Usable capacity comes from shelving, rather than square feet, so lay out the shelves before you fix the box size. Keep an aisle free to leave room to turn with a full case or a cart and keep the air path clear so that shelving and product do not block the evaporator (the fan unit inside the box).
Lights and temperature checks
Cold-rated LED fixtures last longer and add less heat to the room. Decide how staff will check the temperature every day. If there is a display outside the door, staff can check the box without opening the door, whereas a simple daily log catches a drifting box before product is lost.
Bring answers, rather than a floor plan
A dimensioned sketch, the door size, and swing, where the compressor goes, and a shelving plan are enough for an installer to quote accurately. Quotes built on the same answers can be compared line by line, and the build has fewer change orders once the panels go up. This makes it simpler and cheaper for restaurant operators to have the
Arjan Dhillon writes about walk-in cooler and freezer planning for World Food Equipment, a Mississauga company that has supplied and installed more than 2,000 walk-in coolers and freezers across Ontario since 1995. Access a free walk-in planning guide can be found here.




